kittencannon09

Fiat 500 Replacement Key Fob If your 500 remote key fob isn't working, it may be time to replace the battery. If you replace the battery and it isn't working, the problem may be elsewhere. United Locksmith specializes in the production of new keys for classic cars. We have all the tools and accessories needed to perform this service. Dead Coin Battery A dead battery is the most common cause of your Fiat 500 keyfob not locking or unlocking the doors. The battery inside the key fob is likely to drain quickly when you don't use frequently enough. If your remote is beginning to show signs of a loss in range or stopped working or not responding, then the battery could be dead. g28carkeys.co.uk inside the key fob is held in place with metal retaining clips. If the clips aren't tight, they can cause problems with the contact, which can stop your remote from receiving power. Use a flathead screwdriver to break open the retaining clip and remove the old battery. Make sure to select a replacement battery with the same kind of voltage, the same size and specifications as the original battery. The key fob can be damaged or corroded by water exposure. Even a short bath in soapy water can harm the electronic chip within. Keep your key fob dry. Water Damage Water damage could be the cause of your key fob's not functioning properly. Key fobs are fitted with rubber seals to protect them from being damaged by light rain or a splash of water, however it is essential to keep your car keys away from the pool, ocean, and washing machine! The key fob has an electronic chip that transmits an immobilizer of your car. The chip allows the 500 to be locked and started. If it gets wet, however, it will no longer function. If you're trying to determine whether your key fob still working, you can clean the internal electronics using isopropyl or electronic cleaner. It is recommended to replace the key fob when it's submerged into salt water instead of trying to fix it yourself. While a replacement fob can cost you a little bit of money, it's a lot cheaper than having to pay for your Fiat 500 to be towed to the dealer for repair! You can also fix it yourself by following just a few steps. Be sure to use the correct type of battery before you attempt to open your key fob. This is a job that's more straightforward than it appears, and you can find step-by-step instructions online for virtually any key fob for cars. Faulty Chip The chip inside the key fob communicates directly with the immobiliser on your car to ensure that your vehicle will only start when correct keys are inserted. If the chip is damaged or corrupted, your car won't start regardless of what you do. A damaged chip could occur due to several reasons, but the most common cause is water damage or the battery being dead. Whatever the reason, it's best to delegate this work to a locksmith as they can replace the chip quickly and at a reasonable cost. If your key fob stops functioning after exposure to clean water from the tap or rain, unplug the battery and wipe down the electronic component using a paper towel to ensure it is fully dry before putting it back into. If the key fob does not work, there's a chance that it has damaged components and requires to be replaced. Some people will turn to their dealer when they are in need of an entirely new Fiat key fob, however this could be a costly option. If you are looking for a cost-effective way to get your Fiat key fob repaired then look no further than United Locksmith. We have the equipment and know-how necessary to fix your Fiat key fob in a timely and professional way. Faulty Receiver Module Fiat key fobs send a signal to the vehicle that will unlock and close doors (and start the vehicle for those with an automatic transmission) up to 50 feet. There are many reasons why the fob may not function. This includes a dead battery water damage, worn-out buttons or a receiver issue signal interference or a malfunctioning chip. If the fob was placed in a pocket which has suffered severe trauma (such as being dropped on a hard floor or being washed in the washer), it may not be able to communicate with the Body Control Module (BCM) of the vehicle. This is because the BCM is secured and will only accept signals from a genuine original key and not another. You'll have to replace the fob in case this happens. A professional locksmith is able to handle every aspect of the key replacement process and can even program a brand new one for your 500. They can even offer the fob cloned to work exactly the same way as the original (and costs just a fraction of what it would cost).